#How ot use pl tone in kenwood tk 880. manuals
#How ot use pl tone in kenwood tk 880. full
#How ot use pl tone in kenwood tk 880. software
#How ot use pl tone in kenwood tk 880. series
#How ot use pl tone in kenwood tk 880. download

#How ot use pl tone in kenwood tk 880. software

Often the Kenwood software is less than $100 so don't be a cheapskate just purchase it.ДЇor M/A Com/Harris/GE, etc: there are two software packages that program all current and past radios.

#How ot use pl tone in kenwood tk 880. series

Typically each series or individual radio requires its own software package. Please use Google or some other search engine to find a dealer that sells the software. The various other vendors often permit their dealers to sell the software online (i.e., Kenwood). To obtain Motorola software see the Sticky in the Motorola forum. It is YOUR responsibility to properly word your request. We do not want any hurt feelings when your vague post is mistaken for a free request. If you are having trouble legally obtaining software please state so. Your PM's are not private and the administration has the right to read them if there's a hint to criminal activity. Even if you attempt to engage in this activity in PM's we will still enforce the forum rules. The same goes for any private transaction via Private Message. Making a request such as this is attempting to engage in software piracy and this forum cannot be involved or associated with this activity. All requests will be deleted and a forum infraction issued. Please do not make requests for copies of radio programming software which is sold (or was sold) by the manufacturer for any monetary value. I hope this helps everyone who has questions about these radios.To anyone looking to acquire commercial radio programming software: Use the kenwood software from that point forward to change the radio settings. After that the SJI Software will be useless. From here use the Flash program that comes with the Kenwood Software to upload the factory firmware. When you turn it on hold down the SCN (Scan) button while turning it on.

#How ot use pl tone in kenwood tk 880. download

To flash the factory firmware, use the SJI firmware to download the mod-plug from the radio, check off under 'Enable Modes' (Flash). However, the radio can be easily programmed using the software from hotfire on the SJI Firmware if you don't want to go through flashing the factory firmware. I have the firmware and so does half the users on the Yahoo Kenwood Forums.

#How ot use pl tone in kenwood tk 880. manuals

There are a lot of options with these radios, the manuals and circuit diagram information is easily found on google. Programming the radio and understanding the software may take a little time but overall its pretty easy to understand. This is also good for attempted to contact repeaters that require a CTCSS Tone or DCS Tone to activate the repeater. The radio also supports CTCSS and DCS Signalling which is using a lot on Ham 70cm and good in preventing other conversations that are on the same channel but not directed to your radios from being herd (filtered out). The face plate is reversible allowing the speaker to be on the top or bottom of the radio (depending on installation option). They also support PA (Public Announcement) but require a special plug (KCT-19) and Voice Inversion Scrambling support which also requires an option board to be installed.

You can also link them to a computer and send short messages to a remote radio over Fleetsync or a pre-defined message using the buttons on the front panel to a specific station or all stations (All Call). All from using DTMF signaling from a remote station. Remote Honk Alert with confirmation tone, Remote disable/enable TX, and Radio disable/enable with confirmation tone.

The radio also has scan support and this works with LTR and conventional channels. These radios do support Fleetsync Enhanced Protocol and allow for unit to unit calling and Radio (Caller) ID Support.

#How ot use pl tone in kenwood tk 880. full

However, if the radio is used to its full potential using a Ham Repeate r or Commercial LTR Repeater you can easily stretch 100 miles or more depending on the repeater height and configuration. They can very easily go much further the higher up you are. Using a roof top mag mount Antenna, I've been able to talk from Vehicle to Vehicle up to 10 miles away (Simplex on flat ground non-obstructed (I was on the highway at the time)). The radio is able to be programmed down to the 440Mhz range (70cm HAM) along with GMRS and of course UHF Commercial frequencies (which was the radio's intent). I chose to flash the radio back to the latest Kenwood firmware. To make these radios work you will need to order a programming cable, however, he does have the software required to change the programming of the radio. He has been extremely helpful with these radios. So far I've ordered 2 of these radios from this seller. Kenwood TK-880-H1 w/ SJI Firmware from Hotfire!